Minions in Dungarees, free tutorial challenge for Beads of Courage

Make a minion challenge for Beads of Courage

I was making some Minion beads for Beads of Courage the other day based on Heather Sellers fabulous make a Minion Challenge

I made one of them kinda oval just for fun and he looked like he was missing his dungarees so I decided to dress him and thought it would be nice to follow in Heather's footsteps and throw out a Minion making challenge for Beads of Courage too. 

So I challenge you all to make a minion and send it in :-D

UK Bead Donations:
Beads of Courage, Inc.
 c/o Diane Watt
 14, Radlow Crescent
 Marston Green
 Birmingham,  B37 7LZ

US Bead Donations:
3230 N. Dodge Blvd. Suite J
Attn:  Bead Donations
Tucson, AZ  85716

Canadian Bead Donations:
PO Box 71142
Silver Springs RPO
Calgary, Alberta  T3B 5K2

Firstly you will need to make some thick yellow stringer 2mm approx, some thick blue stringer 2mm approx and black stringer 1mm approx.

Wrap a wide footprint of blue glass on to your mandrel - I use the smallest cavity on CG Bead roller BR-46 large chunky oval to shape these oval minions. If you are hand shaping then aim to create a footprint that will be between 1/3 to half the length of your final bead.

Using a roller or by hand shaping with a graphite paddle, shape the wraps to form one half of an oval bead. If the flat end of your half oval has a pucker, gently heat and roll the bead against the side of your mandrel to remove the pucker to  minimise the chance of trapping a large air bubble in the middle of your bead when you add the yellow glass.

Add some wraps of yellow glass next to the blue taking care not to trap any air bubbles between the two colors.

Hand shape the yellow glass with your paddle to from the second half of your oval base bead or if using a roller, gently heat and press your bead into the roller cavity. Turn the mandrel a little between each press until you have created a balanced and smooth two-tone oval that will rotate freely in the roller cavity. If you have too much glass you can remove small quantities with a pair of long nose tweezers.

Wrap a line of thick yellow stringer around the blue half of your bead leaving a thin strip of blue at the centre which will create the straps of your Minion's dungarees. next wrap a thin line of black stringer around the yellow half of the bead near the bead hole.This will form the band for his goggles.

Melt your stringers in flat and then press your bead with some mashers, between two graphite paddles or with a parallel press. Don't worry about removing any chill marks at this stage as they will be removed during the next stages as you add further detail.

Take your blue stringer and create the "bib" part of your Minion's clothes by placing two swipes side-by-side that join up the dungaree braces to to the trousers. Repeat this for the back side also. Decide which face is going to be the front of your minion and place a small black dot where you would like the Minions mouth to be.

Melt all of the raised decoration in flush on both faces of the bead by warming the raised areas through and pressing them down gently with your graphite paddle. Once everything is flush partially mask your black dot with an offset dot of yellow to create the Minion's smile.

Melt the yellow dot in flat and then place a large grey dot from a full sized rod in the centre of the headband.

Flatten the grey dot but leaving it a little raised and then top the grey dot with white glass. Flatten the white dot also, leaving it slightly raised so that the dots are stacked up.

Top the white dot with a large blob of clear glass and let the clear glass round off to form a lens shape in the flame.

Choose your minions eye colour and place a small dot over the clear lens to create the iris. Next pick up your black stringer again and add a tiny dot to the eye to for the pupil. You can chose to add some more final last details at this point if you like, such as buttons and further details on the goggles. Warm your bead through and pop it in the kiln to anneal.

Minion beads are very well loved and treasured by Beads of Courage kiddos so it would be great if you wanted to give making them a whirl!

Have a lovely evening, Jo x
 
PS. This tutorial is written for bead makers with prior experience in mind. Please take all safety precautions when working with a very hot flame including proper eye protection and please do work in an adequately ventilated work space.

This tutorial is fan art and is not to be used for profit. It has no connection with the creators of Minions.